|
Frequently Asked Questions Of Technics
SL-1200Mk2/SL-1210Mk2 Turntables.
( [Almost] Everything you ever wanted to know about your 1200 )
Revision 2.2 - January 18, 1994 Copyright (C) 1993,1994 Steve Valdez
New in 2.3:
* minor revisions and information additions... (marked with a ##)
* Cartridge spec list
comments & submissions welcome, corrections wanted.
IMPORTANT: Use this information at your own discretion -- if you screw
up your turntables it isn't my fault. Treat this FAQ as being purely
anecdotal - I won't guarantee accuracy. If you go ahead though, be
sure you have a solid idea of what you are about to do and observe all
electrical precautions where pertinent. You should have some
electronics experience if you open up your deck.
Initially this was going to be only a tweaker FAQ but there isn't that
much more general stuff so I put it in anyways. This info checks out
on Technics SL-1200Mk2 and SL-1210Mk2 turntables. I haven't looked at
SL-1200Mk3 turntables which are supposed to have improved electronics
over a standard Mk2. The physical stuff will be the same though. Also,
the electrical information applies to the Technics SP-25's (they use
the same drive electronics/motor). SP-25's are broadcast turntables
FYI. This is all pretty easy stuff but if you need a more detailed
explanation ask for help.
I've given up on the tonearm disassembly - I've done it but you need
pictures to describe how to take it apart/put it back together. This
also includes replacing the locking clip and calibrating the
anti-skate knob as both require extensive disassembly. If I'm in a
good mood I may try to describe the process in the future.
TABLE OF CONTENTS:
* 1.0 - 1200 history
* 2.0 - Tonearms & Cartridges
+ 2.1 - Balancing your tonearm
+ 2.2 - Other tonearm/cartridge stuff U may wanna know
+ 2.3 - Picking a cartridge
+ 2.4 - Slipmats
* 3.0 - Disassembly of your 1200
+ 3.1 - Removing the top
+ 3.2 - Removing the rubber bottom
* 4.0 - Advanced Tonearm & Headshell adjustments
+ 4.1 - Tightening the tonearm suspension
+ 4.2 - Tightening the headshell locking ring
* 5.0 - Pitch Controls
+ 5.1 - Adjusting the pitch gain (i.e. more than +-8%)
+ 5.2 - Adjusting the slider for true 0 at center
* 6.0 - Other Hacks, Adjustments & Fixes
+ 6.1 - Adjusting the braking
+ 6.2 - Eliminating the annoying ground wire
+ 6.3 - Replacing the pop-up lights
+ 6.4 - Fixing the power switch when the top comes off
1.0 - 1200 HISTORY
Sometime in the early 70's Technics released the original SL-1200 as a
hi-fi turntable. Then sometime around 1978-79 they did some work
improving the motor, redesigning the casing, adding a separate ground
wire, etc. and released the SL-1200Mark2. This is what the majority of
DJ's have and this design still endures today. The SL-1200Mk2 is the
only version officially authorized for sale in the U.S. by Technics.
The following derivatives are available on the gray market in the U.S.
and are international versions (110/220V). The SL-1210Mk2 is
essentially the 1200Mk2 except in black. Everything else is the
same(## word has it that the 1210 is lighter than the 1200 and is more
susceptible to rumble, etc.). (## To confirm that the 1200 and 1210
Mk2's are the same electronically speaking, the service manuals are
identical for either model.) The SL-1200Mk3 is also in black but is
supposed to have a better motor and other improvements.
The best price on a US version 1200 is from ProSound & Stage mentioned
above in the L.A. area. They sell them for $399. There are a bunch of
places in the L.A. area and in N.Y. which sell (likely international
versions) 1200's and 1210's for around $367. In the LA area, try
Quality Electronics on Santa Monica Blvd. (Hollywood?) or Astro Sound
somewhere in the valley. Get a hold of the L.A. Recycler for phone
#'s... The 1200Mk3 goes for $499 at ProSound & Stage. These stores
probably offer their own warranties as Technics/Matsushita will not do
any kind of warranty work on non-US models.
If you want to find out what region of the world your deck was
destined for look at the SERIAL NUMBER label. This is not the black
label on the back. Some of you don't have this info printed next to
your serial # so you'll be out of luck. Next to the serial number is
the model number: "SL-1200MK2-MC" The "MC" part tells you where it was
destined for:
* M - USA
* MC - Canada
* E - Scandinavia/Switz.
* EK - UK
* XL - Australia
* EG - Germany
* EB - Belgium
* EH - Holland
* EF - France
* Ei - Italy
* XA - The rest of the world (I think they also use XG here)
There are also a few other codes not worth mentioning. An easy way to
tell if it is NOT a US version is to look for the 110/220V switch
under the platter. The other giveaway is a Euro-plug with a
US-adapter.
2.0 TONEARMS & CARTRIDGES
2.1 Balancing your tonearm
I've seen many differing methods for doing this so I've included
descriptions from others on the ways they do it:
Method #1:
The way I do it with Stanton 500AL's: mount the cartridge in the
headshell pulled almost all the way to the front. Make sure it looks
straight in relation to the headshell when you put it down on the
record - readjust as necessary. Put the height ring at 2.5mm. For most
purposes I reverse the weight on the tonearm, push it all the way
forward and set the anti-skate to the max. If you try scratching and
the needle jumps back a lot turn it down in 1/2-gram increments as
necessary. Pete Ashdown's method below is the same way I set it up for
listening to my collection. Except I put the weight at about 2.25
grams. No coins on either setup. You should really look at your
technique if it skips no matter what you do. I reserve coins for
really bad situations like springy floors. Some may not like the
reversal of the weight but unfortunately, the 500AL's need at least
about 3 grams for scratching, and calibrating it the way you are
supposed to get's you at most about 2.5 grams.
Method #2:
Written by Pete Ashdown
pashdown@slack.sim.es.com
This is what I ended up with on Stanton 680 cartridges.
Use the included weight that comes with the Technics head shells. Put
a record on so you don't damage the needle, then swing it out over the
record. Adjust the weight until it "floats" level above the record.
Turn the weight indicator to "0". Now adjust the height until it is
close to the surface of the record. This was 1.5 for me. Adjust the
weight to 1.5 for just home listening, 3.5 for practicing and
performance. Use an unpressed side of a 12" or a 12" with a large run-
off to set the anti-skate. Put the needle on unpressed vinyl and
adjust the skate (while spinning) so it stands still. On 1.5, it
should be about 1.3. On 3.5, you can't adjust it high enough, so just
crank it to the max.
After much discussion on the bpm mailing list, the consensus on
anti-skate settings is to set it at 0 if you scratch mix or at a
number equal to the weight on the cartridge if you just listen to your
records without touching them... The idea is that the anti-skate
mechanism in the turntable is designed for normal record playing. A
side note: several of the 1200's I have worked on do not have the
anti-skate knob properly calibrated much like two decks with two
different speeds at a scale setting of +1%.
If anyone else has successful balancing techniques that differ
significantly from what has been already described get in contact with
me.
2.2 - Other tonearm/cartridge anecdotes
It's supposed to be a DJ's secret that angling the cartridge inwards a
few degrees (5-15) helps keep the needle in the groove when
scratching. I haven't tried this but if you do be forewarned that this
may wear out your records faster. It would probably be a bad idea to
try this with non-spherical styli as well.
I saw FM20 (QBert et.al. and crew - 1992 DMC champs) perform here and
I noticed that they had their tonearm heights maxed out and were not
using any Stanton carts (xcept for one deck with a 500AL when they
replaced a headshell). There are supposed to be Shure carts perfect
for scratching -- I don't know which ones. Some people set their
height rings to 0 though.
A more accurate way of aligning your cartridge in the headshell is
with a GeoDisc from Mobile Field Sound Labs (?? - they press up those
gold CD's nowadays) probably hard to find but I have one at work.
Some say that the headshells on the 1210's vibrate more than those on
the 1200's but on the 1210 I had for a while it wasn't any different
from the 1200's. My guess is that the adjustments were done less
critically on the 1210's since they aren't 'officially' offered for
sale in North America and much of Europe. Read below if yours does.
2.3 - Which cartridge to get?
* Stanton 500AL's are cheapest, decent, and can take a lot of abuse.
You can run down to Radio Shack and get one in an emergency if
necessary. Be careful not to buy the broadcast versions - make
sure the needle is in WHITE plastic - NOT dark blue. If you get
stuck with a blue one you can buy a replacement styli and replace
the blue one. The model to look for is D5107A. This is the same
one RS sells. You can also replace the styli with the D5107E which
gives you the elliptical stylus.
* Stanton 500EL's are rugged, have a better freq.response over the
straight AL's (due to the elliptical styli) and still relatively
cheap. Basically the same cartridge body as the AL xcept with the
D5107E styli.
* Stanton 680EL's are popular with a lot of people for the
elliptical needle (to help keep the needle in the groove) and for
the slightly better response over the 500's. The 680AL has the
spherical styli on it me thinks.
* There's the new Stanton 890 which costs a lot but which has the
20-20k response. I haven't seen anyone using these...they probably
behave the same as 680's from what I gather. Ortofon's (in
general) look sharp and sound a lot better than Stanton's but are
hard to find, expensive, and you can't put coins on the
* Concorde Pro (xcept maybe if you have Danish coins...). You can't
beat the ease of installation with a C-Pro though.
* There is a Shure line but as mentioned above I'm not familiar with
them at all. (someone needs to fill me in...)
The general feeling I've gotten from bpm and others I've talked with
is to get 500's if you are a scratching DJ, 680's for normal club
mixing, Ortofon's also for club-use with a much better sound.
Vital Specs List:
*******************************************************************
Model(price) TrackForce Stylus FreqRange Separation
******************************************************************
STANTON
500AL 2-5 gm spheri. 20-17kHz 28db
500EL 2-5 gm ellipt. 20-18kHz 30db
680AL 2-5 gm spheri. 20-18kHz 28db
680EL 2-5 gm ellipt. 20-18kHz 30db
890AL 2-7 gm spheri. 20-20kHz 30db
ORTOFON
C-Pro
C-Pro N/C
Concorde
SHURE
I have the specs for all the Stanton stuff, if anyone needs more
specific information other than what is listed get in contact with me.
People with specs on the Ortofon's and Shures's PLEASE get the info to
me!
2.4 - Slipmats
Most people have found the 'wonka' slipmats to be the best. Sorry, I
don't have a source with me. Avoid slipmats which are
printed/silk-screened - they wear off and look bad pretty fast. This
includes those "Technics" slipmats made in Belgium. Either try getting
dyed ones or make your own. Some suggestions to try: felt from the
fabric store, an old record in it's plastic sleeve, thin foam packing
sheets (Like the stuff your 1200 was packed in). Use a piece of paper
to tighten up center holes which are too loose. (put a small piece of
paper on top of the spindle and put the record on top)
3.0 - DISASSEMBLY OF YOUR 1200
What you'll need for the mods (read text for detail):
* #1 Philips screwdriver
* jewelers philips screwdrivers
* power driver
* multimeter
* soldering iron + solder
* wire
* wire stripper/cutter
* electrical tape or that heat-shrink stuff
3.1 - Removing the top ( for access to the circuit board )
1. unplug the TT, remove the platter, secure the tonearm.
2. use a Philips screwdriver to remove the 5 screws holding the
plastic cover under the platter.
3.2 - Removing the rubber base ( access to tonearm, cue light, power switch,
basically everything else. )
1. unplug the TT, remove the platter, secure the tonearm.
2. There are a few ways of doing this. You can use the hard plastic
dust cover that came with your TT or you can find a rectangular
milk crate. Or if you have a coffin (or similar case) you could
turn it 90degrees to the way you normally put it in. Turn the deck
upside down. If you use a crate you may want to tape it in place
to keep it from falling in. Be careful with the tonearm.
3. remove the feet by unscrewing them.
4. Use a power driver (or regular screwdriver) to remove all 21
screws holding the rubber base.
5. Be careful with the cables as you pull off the base.
6. Remember: the 4 long screws go under the feet, the short screws
with large washers go in the center circle, and the metal screws
(medium length) go along the edges.
4.0 - ADVANCED TONEARM & HEADSHELL STUFF
4.1 - Tightening the suspension on your tonearm
Some TT's have tonearms which seem to be loose. If you grab the
tonearm and pull it gently back and forth and it seems loose you can
tighten it. It shouldn't move at all. A loose suspension can severely
affect it's performance - from jumping needles to binding.
It's pretty easy to tighten the suspension. You'll need a small flat
screwdriver and a large one. Use the large one to loosen the outer
locking screw on the top of the pivot point. Now use the smaller
screwdriver to loosen up the smaller screw. Put a drop of oil where
the bearings are (under that top support on the other end of the
adjustment screw) so that it doesn't bind. Now tighten the small screw
slowly until it just contacts the bearings. Adjust the tightness so
the tonearm doesn't wiggle if you pull on it but leave it loose enough
for the tonearm to pivot freely without binding. Adjust carefully and
don't overtighten otherwise the bearings will be damaged! When done,
tighten up the locking screw.
4.2 - Tightening up the headshell locking ring
Have you put on your headshell, twisted that knurled tightener at the
end of the tonearm as tight as possible and have found that the
headshell still moves around? What will happen is that the headshell
won't sit parallel to the record but may be tilted as a result of
twisting of the headshell. This usually occurs when you change
headshells a lot or if you've had your turntable for a while, and can
contribute to needle jumping so here's what you do to fix it.
First read 3.2 on base disassembly. Remove the rubber base. There will
be this big piece of hard black plastic covering almost everything.
You'll need to remove it. To remove the tonearm assembly look for
three screws (all formerly under that black plastic) and unscrew them.
Be careful not to drop the tonearm when you remove that last screw!
Now, remove the tonearm assembly from the rest of the 1200, and look
at the bottom of the tonearm where the headshell is put in. There will
be two tiny philips screws there. Get a jewelers screwdriver of the
CORRECT size and tighten those up. Put the headshell on and try
wiggling it to make sure everything is right. Now put your tonearm
back on and close everything back up.
5.0 - PITCH CONTROLS
IMPORTANT: Make sure you have the pitch slider set at the center (0%)
if you make any of the two following adjustments.
Also, the pitch gain on one 1200 is not necessarily the same on
another 1200. Or, a +6 according to the scale on the first 1200 is
probably not the same speed as a +6 according to the scale on the
other.
5.1 - Adjustment of pitch gain
Some have said that you can get +-15% pitch gain by doing this but on
the decks that I have tried this on it doesn't get up that high. One
consideration if you try this is that it gets harder to zero in on the
exact speed when mixing beats.
Remove the top panel under the platter as described above. Look at the
upper right hand corner of the PCB (printed circuit board). There will
be a colored pot up there (blue) which sez "pitch" next to it. Use a
multimeter on the pot to get a reference before turning it if you want
to get back to where you started from. (test for resistance, one clip
to the lead facing the back, the other on the lead to the right)
Turning to the right should increase the gain (greater than +-8%) and
vice versa. The pot is a little touchy when it comes to precision
adjustment. There's a way to get it into factory spec with a frequency
counter but I don't remember how at the moment.
5.2 - Adjusting the pitch slider to 0% at center
Contrary to (popular?) belief there is no way to lose true 0% pitch
when the slider is in the middle - no matter how you hack it. When in
the middle there is a switch which is thrown which bypasses the pitch
slider and the motor is now crystal locked at the exact speed. But, if
your deck is messed up in this area when you move the slider in the +
direction, for example, it will slow down at first and will then move
to 0 and then will speed up as you move it more in the + direction! In
other words you now have 0 at two places. So this is for reference if
you need to get your pitch slider so that 0 is really in the center.
Open up the base, look where the pitch pot is. There will be a hole
about 3-5mm in diameter where you can see a small pot on the other
side. Hook up a multimeter to that pot (again, connect to the center
lead and the one nearest the edge of the board I think) and use a
small adjustment screwdriver to adjust it to 2.7kOhm.
6.0 - OTHER HACKS / FIXES
6.1 - Adjustment of braking
Doing this you can get your decks to brake hard enuff to make it spin
backwards when you hit STOP. Most decks have this set correctly but if
yours isn't then you can do this. Pop open the top as described, and
look for pot VR201 - It's on the right side next to the blue pitch pot
described above and says "brake" next to it. Turn it to the right to
increase the braking time. I suggest you just nudge it a little to the
right and see what happens by placing the platter back on and playing
with the start/stop button. Make sure you unplug the turntable from
the wall before taking off the platter again. Note that it takes
slightly more force to stop a platter w/record vs. an empty platter.
6.2 - Eliminating the ground wire
This may work only with certain setups -- to be sure: use a multimeter
and do a continuity check between the ground screw on the back of your
mixer/pre-amp/whatever and the outer conductor of the RCA jack inputs.
Check both channels. Not all systems share a common ground. If it
does, remove the rubber base from your TT. Remove the screws to the
plastic stress clip for the cable coming out from under the tonearm.
Dissasemble the clip. Remove the two screws holding down the round
plate. Move it out of the way. Use two short lengths of wire and
solder both to the ground tab the current wire is connected to. Solder
the end of one wire to the shield of one channel in the audio cable
where it is soldered to the PCB, and do the same for the other wire
and channel. You can desolder and remove the old ground wire if you
want. (I left mine on just in case) You may not want to do this mod if
you are using different mixers constantly.
6.3 - Changing the pop-up lights
1. remove the base as described above.
2. remove the two screws holding the whole light fixture from
beneath.
3. Use a jewelers screwdriver ( with the rotating tops so you can
apply pressure while turning ) to remove the small screw at the
bottom of the metal cylinder where the bulb is. Make sure to get a
correct size screwdriver as some decks have this really torqued
in. (read below)
4. If you are a DIYer it's a ~20VDC bulb. Be careful here or you may
kill your turntable (12-14v bulbs won't work - they glow faintly
when the cylinder is down and burn out too quickly - they sure are
bright though) You'll need the right size too, some may need a
slight modification to fit--use the soldering iron to burn off
some of the glue at the base.
If you aren't a DIYer you'll want to read this:
From: Dario Alcocer alcocer@adoc.xerox.com
...As far as the replacement bulb was concerned, I played no games;
I contacted an electronics shop in Oakland that's an authorized
Panasonic/Matsushita dealer, and ordered _two_ lamps (just in case I
messed up). I ordered them, and they arrived via UPS 3 days latter.
I think the lamps were kind of pricey, around $4.95 each. By the
way, If anyone needs it, I have a list of authorized dealers that I
can e-mail or fax to you.
[EdNote: It's Cass Electronics in Oakland,CA and the part number is
SFDN122-01 : "Lamp, stylus illuminator" ]
5. Using a small precision (jeweler's) screwdriver, remove the
polished aluminium shell to expose the bulb.
[This is where you have to be a little careful and patient. Since
the screw was torqued in pretty good from the factory, what I did
was used a pair of pliers to turn the screwdriver, while pushing
down firmly to keep it from stripping the screw head. Since the
screw is pretty small (and easily stripped), MAKE SURE you have a
screwdriver that fits the screw EXACTLY; even if you have to go 40
miles to a store to buy the right screwdriver, do it. After all,
if you paid nearly $400 US to buy a 1200, don't cheat yourself by
buying a cheap screwdriver that can damage it.]
6. Remove the bulb from the lamp housing and clip it off from the two
wires as close to lamp as possible. You'll want to leave enough
wire left over, just in case the bulbs you get don't have long
enough leads.
7. Solder (or twist) the wires of the bulb to the corresponding wires
coming from the turntable.
[EdNote: Make sure you use electrical tape or shrink tubing on
each wire when done!]
Insert the new bulb into the lamp housing and re-attach the
polished aluminium shell.
Re-install the lamp unit into the turntable. Before you replace
the bottom rubber base, test the pop-up switch to make sure that
the bulb leads won't get caught. If there is too much spare wire,
you'll either remove the excess or just tuck it out of the way.
Replace the bottom rubber base, and install the four rubber feet.
Connect power cord, and make sure the light bulb lights and pops
up cleanly.
This whole procedure should only take 10-15 minutes at the most. Best
of all, if you have the right tools (precision screwdriver, regular
Phillips screwdriver, and a set of pliers) it should be an easy thing
to do.
6.4 - Fixing the power switch when the knob comes off
Have you ever lost the shaft -- when you happen to twist the black
knob right off? If you turn your TT upside down it won't come back so
you'll need to do this: remove the base as described above and look
where the power switch is. Push the shaft back up and reattach the
black knob. You may want to put a drop of glue in the knob
center/bottom before replacing it to help prevent this. Or you could
just tape down the knob and use a power strip to turn your TT on and
off.
Remember, comments/submissions are always welcome. If there are errors
let me know.
Copyright (C) 1993,1994 Steve Valdez
|
